Request Information
Maximator® air amplifiers are designed to boost plant air pressure or increase the supply air pressure at work stations and pneumatically operated machinery when the available working pressure is insufficient.
Air operated tools become more efficient when coupled with air amplifiers. These amplifiers are capable of generating pressures from 30 psi to 4,350 psi.
Air amplifiers do not need electrical power, since they use the same compressed air source for both driving and amplifying. This ensures quick installation and cost effective operation.
Air amplifiers can be controlled to automatically stop once the desired end pressure has been reached. The amplifier will restart when a drop of only 1% from the stall pressure has been detected.
Single stage - single acting and single stage - double acting air amplifiers are available to satisfy most pressure and flow demands. Amplifiers are ideal for intermittent pressure requirements.
MAXPRO® offers complete turn-key systems for easy installation. In addition, technical application and service support is available for all air amplifiers and turn-key systems.

See some photos of air amplifier systems here.

Unit of Measure

Style

 N/A Single Acting

Minimum Supply Pressure

 N/A 30 psi

Maximum Supply Pressure

 N/A 725 psi

Maximum Rated Pressure

 N/A 725 psi

Stall Pressure

 N/A 5 Pa

Inlet Connection

 N/A 3/8 in. FNPT

Outlet Connection

 N/A 3/8 in. FNPT

Maximum Temperature

 N/A 140 ºF

Weight

 N/A 35 lb

Length

 N/A 16.63 in

Width

 N/A 6.75 in

Height

 N/A 10.75 in

Mounting A

 N/A 9.00 in

Mounting B

 N/A 3.13 in

Mounting C

 N/A 0.44 in

Features

 N/A
  • Air pressures from 30 psi to 4,350 psi
  • Compact, lightweight design
  • Easy installation and operation
  • Single or double acting
  • No electrical power required
  • “Stall” at target pressure, automatic restart after a drop of only 1% from target pressure
  • PTFE SEALS
  • Unregulated pilot air port for easy restart and better control on all DLA, SPLV2 and GPLV2 models (1/8" FNPT)
  • Standard and custom application designed systems

How an Air Amplifier Works

 N/A Air Amplifiers are intended for use in boosting existing plant air to higher pressures. Each amplifier has a spool valve that acts like a 4-way directional control valve. Plant air is supplied to this spool valve which automatically cycles back and forth. The plant air that is fed into the spool valve is alternately directed, as the spool cycles, to the main air drive piston in the air drive cylinder. This causes the piston to cycle back and forth in the amplifier.
There is also a high pressure section where the air, that is to be pressurized, is supplied. The air flows into the amplifier pressure chamber, through the inlet check valve(s), on the suction stroke and is pressed out of the chamber, through the outlet check valve(s), on the discharge stroke. The reciprocating movement of the air drive section, connected directly to the high pressure section, creates a positive displacement of air through the inlet and outlet check valves.
There are single and double acting models available. The single acting amplifiers displace air once per full cycle. The double acting amplifiers displace air every stroke, or twice per full cycle, providing higher and more constant flows
These amplifiers can be installed in any position, but vertical mounting is best for longest seal life.
All connections to the amplifier must be run with equal to, or greater than, the connection size in the amplifier.

Note

 N/A
  • The air to the amplifier should be filtered to between 5µ and 40µ and have a dew point between 0ºF and 50ºF. Very moist air can wash out the seal lubricant and very dry air may require a lubricator.
  • Pa = Air Drive Pressure (PSI) Ps = Supply Pressure (PSI)
  • Maximum air drive pressure 145 psi
  • Maximum operating and stall pressures must not be allowed to exceed output pressure rating.
  • The 9/16-18 is a 1/4" O.D. tubing, high pressure coned and threaded connection, all other connections are FNPT,
  • Air drive inlet connection on BPLV2 and MPLV2 is 1/4" FNPT.
  • Air drive inlet connection on all other air amplifiers is 1/2" FNPT.
  • There is a 1/8" FNPT pilot port on all amplifiers, except BPLV2 and MPLV2, that must be plumbed from air source.